Modul CS

Modul CS

Advantages at a glance

  • Stabilising leg or liquid and bulk tippers (rear) 
  • Support while unloading
  • Levelling due to two seperate landing gears
  • Low maitenance because of integrated lubricant cartridge
  • High degree of installation variability thanks to double bolt hole pattern
  • Additional spindle nut
    - Additional protection against wear and tear
    - Minimal risk of accidents

Technical Features

  • Protected against wear by fully sealed gearbox and reinforced inner tube
  • Full length back plate for high variability during installation
  • Reinforcement for maximum bending strength
  • Heavy duty shaft for better shock resistance
  • Secure stand due to reinforced rigid foot

Technical Specification

* Bracing lugs are supplied loose

Note:
Dimensions A, B and C, see general information.

Also available without brace lugs on request

Selection table / Versions available

Order No.

M (mm)

H (mm)

P (mm)

Back plate

Foot

CS 1044700R

750

470

728

full length

T rigid

CS 1054700R

700

380

678

full length

T rigid

CS 1064700R

650

380

628

full length

T rigid

CS 1084700R

600

330

578

full length

T rigid

CS 1094700R

550

280

528

full length

T rigid

Technical Data (per piece / set)

Characteristic

Value

Lifting capacity

12 t/ 24 t

Static load

33 t / 66 t

Lift per turn of handle

 

- Low gear

0,9 mm

- High gear

15,0 mm

Crank force at 8 t lifting capacity

110 N

Remarks

Please order crank handle separately, see general information.
Two stabiliser legs are required per trailer.
There is no cross shaft.

Modul CS

Item

Description

Remark

Order No.

per set

01

Cover

 

JS E0046100

1

02

Bevel gear with bolts

 

JS E0058600

1

03

Cover with shaft

compl.

JS E0125600

1

04

Grease nipple with protective cap

 

JS E0084000

1

05

Shaft with bearing

 

JS E0084100

1

06

Grease tank

 

JS E0002000

1

07

Gear

 

JS E0055800

1

08

Crankshaft

compl.

JS E0046500

1

09

Bearing holder

compl.

JS E0058800

1

10

Drive

compl., with 05, 07, 08 + 09

JS E0084300

1

11

Bolts, washers, nuts

 

JS E0043100

1

12

Crank 350 mm w. parking hook

with 11, 13 + 14

JS U01

1

12

Crank 415 mm w. parking hook

with 11, 13 + 14

JS U02

1

12

Crank 450 mm w. parking hook

with 11, 13 + 14

JS U03

1

12

Crank 480 mm w. parking hook

with 11, 13 + 14

JS U04

1

12

Crank 520 mm w. parking hook

with 11, 13 + 14

JS U05

1

12

Crank 570 mm w. parking hook

with 11, 13 + 14

JS U07

1

12

Crank 620 mm w. parking hook

with 11, 13 + 14

JS U08

1

13

Crank bushing

 

JS E0042700

1

14

Crank parking hook

for crank 350 mm (JS U01)

JS E0040200

1

14

Crank parking hook

for crank 415–480 mm (JS U02-JS U04)

JS E0040201

1

14

Crank parking hook

for crank 520–620 mm (JS U05-JS U08)

JS E0040202

1

15

Axial bearing

 

JS E0066400

1

16

Mh-04/750 inner tube r. + spindle and bearing

with 15 + 03

JS E0067003

1

16

Mh-05/700 inner tube r. + spindle and bearing

with 15 + 03

JS E0067002

1

16

Mh-06/650 inner tube r. + spindle and bearing

with 15 + 03

JS E0067001

1

16

Mh-08/600 inner tube r. + spindle and bearing

with 15 + 03

JS E0067004

1

16

Mh-09/550 inner tube r. + spindle and bearing

with 15 + 03

JS E0067005

1

17

Angle

 

JS E010.001

1

PDF-Downloads

Mounting and Operating Instructions
Modul / Optima Landing gear 11/2021
Modul CS 04/2020
Flyer
MODUL CS Stabilizer leg 09/2016

Pictures

Modul CS

You can change your cookie settings at any time by clicking here.